Patented design

Patented design

Automated Warrior Swing-blade Sawmill

10 manual mill 01.jpg

Match prices! Limited time!

10” cut MANUAL machine.

Get a quote from any reputable manufacturer and we will match their price.

All specs matched to the Auto model with heavy duty beam, however - auto feed and auto swing is removed. Earlier design shown.

Our manual 10” machine provides;

20ft cut length.

10” x 10” standard cut.

9” x 20” double cut.

Single end sizing.

Taper log alignment.

Fully upgradeable to power feed and auto swing later on!

$19,500 NZD

Complete Warrior sawmill.

A revolutionary swing blade sawmill that makes the process of milling logs into timber a joy. The operator controls the feed rate through a lever at the end of the beam, allowing 100% speed control while the saw cuts. The operator has total control operating from a single point. Simply swing the blade, power the saw through the cut until the blade swings automatically at the other end. Power the saw back revealing a sawn board. An incredibly versatile, easy to use portable sawmill. We’ve brought the swing blade technology into the 21st century!

Includes: 

  • Electric start.

  • jockey transport wheels.

  • 1 x 4-tooth INSERT blade, tool, extra tips and sharpener.

  • Power feed.

  • Auto remote blade swing.

  • Operable in both auto and manual mode.

Specs:

  • Single end vertical and horizontal sizing.

  • Log setup taper alignment included.

  • 1.3m diameter (4 foot) log - although any diameter may be sawn.

  • 6m (20ft) log cut length.

  • Double cut capable.

Pricing:

Petrol power plant:

  • Model 8 (8" x 8" standard cut, 7" x 16" double cut), fitted with Honda Petrol 27.5hp (gross) engine. $25,000.

  • Model 10 Manual mill. Currently available through the special. (10" x 10" standard cut, 9" x 20" double cut), fitted with Honda Petrol 27.5hp (gross) engine. $19,500 - power feed, auto swing removed.

  • Model 10 (10" x 10" standard cut, 9" x 20" double cut), fitted with Honda Petrol 27.5hp (gross) engine. $28,000.

  • Model 12 (12" x 12" standard cut, 11" x 24" double cut), fitted with Honda Petrol 27.5hp (gross) engine. $35,000.

  • Model 12HD (12" x 12" standard cut, 11" x 24" double cut), fitted Kohler Petrol 40hp (gross) engine. $48,000.

    • NEW Model 12HD

      • Can be upgraded to PLC computer setworks. $10,000.

      • Warrior ‘heavy duty’ frame with canti-levered beam.

      • Heavy duty drive train installed.

      • Extend to very long lengths.

      • Board return system included standard.

Electric power plant:

  • Model 8 (8" x 8" standard cut, 7" x 16" double cut), fitted with 3-phase electric 15hp motor and soft start. $27,000.

  • Model 10 (10" x 10" standard cut, 9" x 20" double cut), fitted with 3-phase electric 15hp motor and soft start. $30,000.

  • Model 12 (12" x 12" standard cut, 11" x 24" double cut), fitted 3-phase electric 20hp motor and soft start. $37,000.

  • Model 12HD (12" x 12" standard cut, 11" x 24" double cut), fitted 3-phase electric 25hp motor and soft start. $47,000.

    • NEW Model 12HD

      • Can be upgraded to PLC computer setworks. $10,000.

      • Warrior ‘heavy duty’ frame with canti-levered beam.

      • Heavy duty drive train installed.

      • Extend to very long lengths.

      • Board return system included standard.

Diesel power plant:

  • Model 8 (8" x 8" standard cut, 7" x 16" double cut), fitted with Kubota Diesel 24hp (net) D902 engine. $32,000.

  • Model 10 (10" x 10" standard cut, 9" x 20" double cut), fitted with Kubota Diesel 24hp (net) D902 engine. $35,000.

  • Model 12 (12" x 12" standard cut, 11" x 24" double cut), fitted with Kubota Diesel 24hp (net) D902 engine. $42,000.

  • Model 12HD (12" x 12" standard cut, 11" x 24" double cut), fitted with Kubota Diesel 24hp (net) D902 engine. $50,000.

    • NEW Model 12HD

      • Can be upgraded to PLC computer setworks. $10,000.

      • Warrior ‘heavy duty’ frame with canti-levered beam.

      • Heavy duty drive train installed.

      • Extend to very long lengths.

      • Board return system included standard.

 

What makes our mills stand out?

  • Open access to load your logs and remove timber (without the possibility of damaging your tracks. You're not stuck in a portal restricting your options.

  • The mono rail means you're mill will always pull straight - its not dependent on how or where you pull. It will cut straight no matter what.

  • Our mills now have a 40hp capacity heavy duty Curtis gearbox (made in the US). The driven pulley is also mounted on the other side of an outrigger bearing - meaning the pressure provided by the belt is off the gearbox. This is the number one fault with most swing blade sawmills.

  • We have full taper ability along with single end sizing, making our mills very easy to align to the log and to set you're sizes.

  • The swing apparatus is effortless. We also have weather board options available to coincide with its simplicity.

  • All our mills have the ability to double cut straight off the log - no turning the mill around (its designed into the concept). Our mills don't require any 180 degree swing function - this facility has no relationship to any extra ability regarding double cutting.

  • Portability. Our mills can be provided with a simple dolly trailer system. They can also be transported via a small jockey arrangement optional with the sawmill. Lots of options for easy 10-30 minute setup/breakdown.

  • A major hidden advantage with our saw is that there is no need to start vertical first followed by horizontal as your finishing cut. Simply start horizontal and finish with vertical - no wedging required. Just grab your cut timber and start again.

  • Sharpening takes literally seconds with our simple 4-tooth saw blade. This design means our mills put LESS strain on the blade prolonging the life of your gearbox, bearings and belts.

  • We have thin-kerf, slabber and planer blade attachments available for all mills.

  • Saw any diameter logs.

  • Price, production, simplicity and portability - you cant beat it!


 

Assembly

Please find attached step by step pictures illustrating how the machine comes together out of the box. Note once the unit is together its very quick to transport with the trailer.

 However even if you did not get the machine with the trailer kit, it’s still relatively easy to disassemble into smaller components for transportation. If it’s possible to leave the beam in full length it would make the process much quicker. It may take around 40-60 minutes to disassemble so that it may fit into a small 3-4m trailer.

 In this example one person has assembled the complete sawmill at an agricultural show within 4 hours (without any heavy lift equipment).

 
MILL WEIGHTS.jpg